Step 1: Disconnect the negative battery terminal To begin with, the negative battery terminal must be disconnected before locating the positive power lead to the switch. This is followed by installing the right terminal end on the power lead wire and connecting it to the battery terminal. Step 2: Connect the accessory lead wire The next step involves connecting the accessory lead wire to the accessory terminal using the right wire terminal. Check out the New in this Version page for a list of improvements for each version.
New in this Version. Inductive Automation is proud to have a Partner Program that allows others to create modules to enhance Ignition's functionality. Anyone looking to create a new module should start here. Ignition User Manual 8. Browse pages. Copy Page Tree. Jira links. Created by Paul Scott , last modified on Jan 05, About this User Manual This Welcome section provides a broad overview and information relating to modules , architectures , installation , and an Upgrade Guide.
Inductive University Inductive University is a free online learning platform designed to help you master Ignition. Ignition Basics Ignition is completely different from what you are used to using. Introducing Ignition. Fast and reliable service. His honesty is impeccable. Juan knows his stuff.
Came back days in advance of his appointed date to resolve. Much appreciated. David 13 years of experience. Request David. Ford Focus L He was very knowledgeable and professional. But the main thing that I appreciated was that he was patient and explained things to me without sounding condescending.
Need Help With Your Car? Related articles. Unless you have a spare key handy, Read more. How to Replace a Ballast Resistor The ignition coil cannot get proper voltage if the ballast resistor is broken. Signs are a crank without a start or a start and an immediate stall. How to Replace the Electronic Spark Control Module The car ignition has an electronic spark control module that fails when the Check Engine Light illuminates or if the engine does not start.
Related questions Battery replaced recently and car still won't start. Only clicks. Hello, since you tried jumping the vehicle with the same result, there are two possibilities. The most likely is that the starter motor has failed. The second is something keeping the engine from turning. To get a complete diagnosis of Car keeps stalling. A check engine light is warning that their is some fault in the pcm or other sub computers, the fact that its stalling and a cel check engine light is illuminated tells me there is definitely a problem with either Anti-theft system activates and car stalls Hey there.
If you have a "chip key", try replacing it and re-programming to recognize the new key. Sometimes the keys will develop faults.
If it is not the key, there is a specific Diagnostic Procedure for this issue in Browse other content. Schedule your Ignition Switch Replacement today! Ignition Switch Replacement. How can we help? Things You'll Need. Related Articles. Article Summary. Part 1. Disconnect the negative terminal on the battery. Locate the battery in the engine bay or trunk of your vehicle.
Use an appropriate sized wrench to loosen the nut holding the cable on the negative - terminal and then slide it off the post. Remove the trim around the steering wheel. There are likely a number of plastic trim pieces between you and the ignition switch. Remove them carefully by either popping them off of their plastic clips or removing the screws and bolts that hold those pieces in place.
In some vehicles, you may be able to replace the ignition switch without removing the steering wheel. Refer to a vehicle specific repair manual for guidance on how to safely remove your steering wheel from the vehicle. You can purchase vehicle specific repair manuals at your local auto parts store. On some vehicles, you'll need a special tool called a steering wheel puller to remove it. Release the clips on the ignition module cover. There may be a plastic cover surrounding the ignition module in your vehicle.
Set it aside someplace safe until you need to reassemble the dash. Part 2. The ignition switch needs to be set to the accessory position before you can release it from the ignition module. Press the release pin inside the hole on the ignition module with a screwdriver. Insert the screwdriver into the hole to press down on the release pin inside.
Slide the ignition switch out. With the release pin pressed, pull the ignition switch straight out of its place beneath the steering wheel.
Have your ignition switch rebuilt if you want to keep the same keys. Some dealerships will rebuild your existing ignition switch if you would rather not have to switch ignition keys. Rebuilding your switch can vary in price based on the application and may not always be available.
0コメント